Mahogany Vaneer Archive The Woodenboat Forum

Order some burl veneer from rockler or some place and contact cement that bad boy on. Then glass over it. The whole shooting match probably wouldnt set you back 20 bucks.

I am in the process of stripping some varnish from mahogany panels inside my boat. After I have stripped some I noticed black spots appearing. Could I have caused them? Or were they there already but hidden in the old varnish? I have tried a coat of varni

I am considering glueing new veneers to the bulkheads in the wheelhouse of my LM 28. From an earlier post it has been suggest to fit thin plywood but I am keen to stay with the existing sapele mahogany, hence the veneer route. My question is has anybody d

Lightweight boat trailer, free images for commercial use business, hydroplane boat kits plans, chris craft rc model boat kits, boats for sale in nc, free small boat trailer plans, private boat sales uk, rf images free.

GENTRY is in a class commonly called a gentlemans runabout, a term popularized back in the thirties. This type of boat conjures visions of a gent in a straw hat accompanied by a blond flapper. This was upper crust boating. The sleek runabouts were beautif

Our mahogany runabout plans are detailed for cold molded planking methods finished off (at least on the topsides) with natural wood mahogany veneers. [There are many photos on the website showing these boats, their construction, and planking.

If you like warm tones, unstained mahogany cant go wrong, like an old lake runabout. If you are going to attempt it yourself mahogany is a good choice, very workable. If you want to go lighter then maple or quarter sawn oak ( like others said ), be aware

I just talked with Dad about that very idea, I think it came up on the WoodenBoat forum too. Hes worried that veneer might delaminate over time in the elements. I think well probably paint the bulwarks but finish the cabin trunk bright. May 3, 2008 at 3:0

Archive] - The WoodenBoat Forum Condon offers many types of Mahogany marine plywood including one called Bruynzeel Regina and another called (Another supplier is Merritt Marine in Pomapano Beach.

Sideboard in Solid Mahogany and Mahogany Veneers. Red Mahogany Stain,Toned Shellac, Trim highlights: Arteza Metallic Acrylic colors mixed and applied by my wife-Eileen M Young. About six months ago I was asked if I could make a revised versio.

After the mahogany transom veneer was glued on to the plywood transom, it was trimmed and then the entire hull was hand block sanded with 120 grit and then machine hand sanded with 320 grit sand paper. With the hull completely sanded we then taped out the

Woodboat Questions, Building Archive. This is an archive of woodboat questions relating to building a wooden boat. Have a browse through the lists of previous questions and responses or just ask, it鈥檚 easy and there is no need to sign in.

Bruynzeel offers us the option for face veneers with many different thicknesses. It allows us to create a panel perfectly matched to the customer鈥檚 usage. Sometimes we need a face veneer the same thickness at the inner plies (usually around 1.5 mm), so th

Monaco. There is something about a classic mahogany runabout that attracts admiration and attention. The flaring concave sides flowing into a reverse barrel tumblehome at the transom, combined with the gleaming mahogany finish, accentuate the sleek flowin

For the front section, I used a hand sander and took the veneer right off. Sanded it with 100, 120, 140 grit sand paper. I used Minwax pre-stain and then finished it off with Minwax red mahogany. From my experience you can sand the veneer right off and ge

Fill the grain to get a perfectly smooth finish. Another way to keep the stain in the filler from darkening your mahogany is to put down a washcoat (a coat of sealer) before the filler. A light, thinned coat of your preferred clear finish works just fine,

I recently purchased a mahogany center console from a 63 Nauset that I am refinishing. In analyzing the center or middle piece of the console, I noticed that the veneer was coming off in large sections. Has anyone peeled the veneer and finished the marine

To get a satisfying result thin, 4 mm, marine plywood with mahogany veneer was placed against the wall with contact cement. The same situation was noticed under the hand wash sink where were a lot of old holes between the engine space and the bathroom.

You will find Veneers - Teak & Mahogany & Others and Boat Lumber products competitively priced on, along with other boat building supplies. Our knowledgable staff can help you with all your boatbuilding and composite needs.

Discover how to make your own veneers & Planking Alternatives (including Cold-Molded Plywood). Changing Plans One reason for building your own boat is getting exactly the boat you want, which presumes finding a perfect stock plan - an often difficult if n

Help w/info on old Yairi? Discussion in ebony bridge, mahogany headstock veneer, tortoiseshell pickguard, 3 + 6 per side To contact the forum owner hit the.

Re: veneer onlay. Posted by George K on Oct 26, 2006. Derik, Ive done a bit of veneer. If you have any questions other than the info here email me at gkrewson.

Birds Eye Maple. Reddish Brown with brownish dots, usually straight grain but can be curly. Medium stiffness, good steam bending. Use for thwarts, decks, paddles, interior furniture. Great for clear finishing. Stock Plank Sizes: 1 x 4 to 10 wide x 6 to 10

Woodboat building questions a Forum for wooden boat building, plans, lumber, caulking compounds and other boat building problems. Wood Screws for Boat Building and Repair. Wood Screws are the most widely used and versatile fasteners used on wooden boats.

Another zenith came in today , the veneer on the top was shot so I replaced it and will do a full refinish on this set, should be a dandy when its done. 6 volt power will come from wind, the owner bought a zenith wind charger and getting it fixed to hook

1938 chris-craft triple cockpit barrel back wooden boat, Description. this sleek beauty is a triple cockpit version of the chris-craft barrel back. kit features: double-planked mahogany veneer hull; vacuum-formed seats.

Messages Archive. He was hired to strip paint and refinish, but found sand throughs after the paint was stripped. A test vacuum pressing with the veneer and my usual urea formaldehyde, on MDF, still looks great. Customer called him this morning and said t

Now I need to finish my veneered mahogany crotch panels and the same procedure will not work because of glue bleed through (wont accept stain) and the fact that I dont want to use pore filler because it will muddy the look of the crotch veneer.

Which means veneer that is just the wood and doesnt have the phenolic and/or paper backer on the backside. Backerless veneer can be trickier to work with. But, it has the benefit of not leaving as obvious of an edge, particularly if youre using it over wo